New consumer unit with SPD and RCBOs installed by Wycombe Electrical Ltd

Consumer Unit Upgrades: What's Involved and Why It Matters

Of all the jobs I do in homes around High Wycombe and Beaconsfield, replacing the consumer unit is the one that makes the biggest difference to how safe a house is. Most people still call it the fuse box, and most people never look at it until something goes wrong.

Every circuit in your home depends on it, and it is also the part of the installation most likely to be decades out of date. So how do you know if yours needs replacing, what goes in its place, and what happens on the day?

Signs your consumer unit is due for replacement

Some boards announce their age the moment I open the cupboard: a wooden backboard, pull-out fuse carriers with fuse wire, or a brown or cream plastic case. Others are less obvious. Frequent tripping, a burning smell, scorch marks around the board or breakers that feel warm are all reasons to call me promptly.

More often, though, I'm called in because the house is changing. A new kitchen, an extension, an EV charger, a heat pump or solar panels all add load and new circuits, and an old board usually has neither the spare capacity nor the right type of protection to take them.

What I fit, and why

Every board I install has a non-combustible metal enclosure, so that if a fault does develop inside it, the fire is contained rather than fed.

RCD protection is the biggest safety gain. An RCD disconnects the supply in a fraction of a second if current leaks to earth, which is what happens when someone touches a live part.

Why I fit RCBOs instead of shared RCDs

On many boards, one RCD protects a whole group of circuits, and on some older ones a single RCD covers the entire house. The drawback is that the RCD can't tell which circuit has the problem. A faulty kettle or a damp outside light trips it, and every circuit on that RCD goes off with it: lights, sockets, the freezer, the boiler, the lot.

An RCBO is an RCD and a circuit breaker combined in one device, and I fit one to each circuit. If a fault develops, you only lose the circuit with the problem. Everything else in the house stays on. You are not left in the dark resetting the board, the freezer doesn't defrost while you're away, and because the tripped RCBO points straight at the faulty circuit, the fault is much quicker for me to find and fix.

It costs a little more than a board with shared RCDs, but I think it is worth it every time.

Surge protection

FuseBox SPD1MT2 Type 2 surge protection device fitted in consumer unit upgrades by Wycombe Electrical

Surge protection is the part most of my customers haven't heard of. A surge protection device (SPD) like the one pictured sits in the board and diverts voltage spikes, caused by lightning or switching on the network, safely to earth before they reach your equipment.

With boilers, chargers, TVs and appliances all full of sensitive electronics, I see it as inexpensive protection for a lot of expensive kit. The indicator windows show green when the device is healthy and red when it needs replacing, so you can check it yourself at a glance.

Built-in fire suppression as standard

FuseBox HA20D heat-activated aerosol fire extinguisher fitted inside consumer units by Wycombe Electrical

This is something I include on every consumer unit I install, at no extra cost: a FuseBox HA20D heat aerosol fire extinguisher. It clips onto the rail inside the board alongside the breakers and needs no power or wiring to work. If there is an open flame inside the enclosure, or the temperature reaches 170°C, it discharges automatically and floods the board with a fire-suppressing aerosol, putting the fire out at its source before it can spread.

I fit it because of one particular type of fault. A loose connection inside a consumer unit can overheat for some time without tripping anything, because no fault current is flowing. The metal enclosure is there to contain a fire; the HA20D is there to put it out. The device has a ten-year service life, and I check it whenever I'm back to inspect the installation.

What happens on the day

I start by testing the existing installation. This matters because a modern board is far more sensitive than an old one. Faults that old fuses have ignored for years, such as damaged cable insulation or a shared neutral, will cause an RCD to trip. Finding these first means I can tell you about them before the old board comes out, not after.

I also check the main earthing and the bonding to your gas and water pipework, and upgrade them if needed, since the new board relies on them to work properly.

Then the power goes off, the old unit comes out, and I fit, connect and label the new one. I test every circuit and record the results. Most domestic upgrades take me a day, with the power off for most of it, so it is worth planning around the fridge-freezer and anyone working from home.

Certification

Replacing a consumer unit is notifiable work under Part P of the Building Regulations. Wycombe Electrical is NICEIC registered, which means I self-certify the work and you don't need to involve Building Control yourself. You receive an Electrical Installation Certificate with the full test results, followed by a Building Regulations Compliance Certificate. Keep both safe, as a solicitor will ask for them when you come to sell.

Fixed quotes, not estimates

At Wycombe Electrical Ltd we prefer to work with fixed quotes rather than variable estimates. An estimate is a best guess that can move once the work starts. A fixed quote is the price you pay, so you get no horrible surprises along the way.

The price of a consumer unit upgrade depends on the number of circuits, the condition of the existing wiring, whether the earthing and bonding need upgrading, and how accessible the board is. That is why I won't quote without seeing the installation first. Once I have had a proper look, I can give you one figure in writing and stand by it.

Book a consumer unit survey

I carry out consumer unit upgrades across High Wycombe, Beaconsfield, Amersham, Marlow and Chesham. If your fuse board is showing its age, or you're planning work that will need more from it, get in touch and I'll come and take a look, or see my consumer unit upgrades page for more detail.